17 - Nov - 2026

The new ESP32 put Wi-Fi 6 and gigabit ethernet on a chip that used to blink LEDs

The ESP32 is by far one of my favorite pieces of DIY tech. It’s the board I reach for whenever a project needs to read a sensor, drive a relay, blink LEDs, or even detect presence with Wi-Fi, all without costing much. Its beginner-friendly demeanor is what’s primarily responsible for its popularity, but that’s also what limits its capabilities.

The ESP32-S31, the next big hardware update to the ESP32, doesn’t abandon that maker-friendly identity, but it does stretch the definition of a microcontroller. Espressif’s new chip combines a 320 MHz dual-core RISC-V processor with Wi-Fi 6, Bluetooth 5.4, an 802.15.4 radio, and a gigabit Ethernet MAC.

The ESP32 finally got a brain upgrade, and it isn’t subtle

Two 320 MHz cores, SIMD, and enough RAM to stop apologizing

The latest specs make the ESP32-S31 sound closer to a compact networking processor than a traditional microcontroller. At its center, you get two 32-bit RISC-V high-performance cores running at up to 320 MHz, plus a separate 40 MHz low-power RISC-V core for background jobs and sleep-state operation. One high-performance core gets a 128-bit data path and SIMD instructions too, allowing it to process several values in parallel for signal processing, machine-learning inference, and similar workloads.

The chip includes 512 KB of high-performance SRAM, 32 KB of low-power SRAM, and 320 KB of ROM. The initial ESP32-S31NRV16 and S31NRV32 versions include 16 MB and 32 MB of octal PSRAM alongside the die, respectively, while allowing simultaneous access to flash and PSRAM.

That allows graphical interfaces, audio buffers, networking, and small machine-learning models to run onboard that would otherwise outgrow the internal SRAM. Both variants use an 8-by-8 mm QFN80 package and provide 60 programmable GPIOs.

ESP32

ESP32-S3

ESP32-S31

CPU

Xtensa LX6, 1–2 cores, 240 MHz

Dual Xtensa LX7, 240 MHz

Dual RISC-V, 320 MHz

SRAM

520 KB

512 KB

512 KB

Wi-Fi

Wi-Fi 4

Wi-Fi 4

Wi-Fi 6

Bluetooth

4.2, Classic + LE

5, LE only

5.4, LE + Classic

Thread / Zigbee

No

No

Yes

Ethernet

10/100 MAC

None

Gigabit MAC

USB

None

OTG, full-speed

OTG, high-speed

GPIOs

34

45

60

Wi-Fi 6 on the S31 is for crowded IoT, not for bragging

2.4GHz only, 20MHz channels, and no invite to the 6GHz party

ESP32 showing internet outage.
Photo by Yadullah Abidi | No Attribution Required.

Wi-Fi 6 is the headline wireless upgrade, but there is a catch. The single-transmit, single-receive radio operates only in the 2.4 GHz band, with no 5 GHz or 6 GHz support. Its 802.11ax operation is also limited to 20 MHz channels in non-access-point mode, while backward-compatible 802.11n can use 20 or 40 MHz channels and reach a stated maximum of 150 Mbps.

As you can imagine, this isn’t Wi-Fi 6 for laptop-style speeds. It is Wi-Fi 6 for crowded IoT networks instead. OFDMA, downlink MU-MIMO, and Target Wake Time can improve airtime efficiency and power scheduling when multiple small devices share one access point.

The radio block also supports Bluetooth 5.4, LE Audio, Bluetooth Mesh 1.1, and Bluetooth Classic, preserving compatibility with older audio and accessory designs. IEEE 802.15.4 adds Zigbee 3.0 and Thread 1.4, while Matter can operate over either Wi-Fi or Thread. That combination makes the S31 particularly great for smart-home hubs and multi-protocol bridges.

Gigabit Ethernet is real, but you still bring your own PHY

The chip has the MAC, you supply the magnetics and the patience

esp32-s31-board-back
Image taken from Espressif’s website.
Credit: Espressif

The other major upgrade is 1 Gbps Ethernet. More precisely, the S31 integrates an Ethernet media-access controller, not the complete physical interface. A finished design still needs an external Ethernet PHY, magnetics, and a connector. Espressif’s Function-CoreBoard-1 demonstrates the arrangement with a separate PHY connected over RGMII, an Ethernet transformer, and an RJ45 port supporting 10/100/1000 Mbps auto-negotiation.

That distinction matters for board cost and pin planning. Gigabit RGMII relies on a dedicated set of high-speed pins, so it’s worth planning your layout early. Designers can instead use RMII when 100 Mbps is sufficient. The Ethernet controller also supports hardware time-stamping aimed at IEEE 1588 synchronization, which makes the chip useful for synchronized industrial and measurement systems.

Cameras, displays, and security

USB High-Speed, JPEG hardware, and crypto that means business

Sensors with ESP32 on a desk.
Photo by Yadullah Abidi | No Attribution Required.

Networking is only part of the upgrade here. The S31 incorporates USB 2.0 High-Speed OTG, USB Serial/JTAG, CAN FD, SD/MMC, dual I2S, multiple SPI, I2C and UART controllers, motor-control PWM, ADCs, DACs, and touch sensing. USB OTG runs at up to 480 Mbps, giving designers a high-bandwidth connection for cameras, storage, audio hardware, and other peripherals.

The chip can connect to 8- or 16-bit DVP cameras and parallel displays up to 24-bit RGB. A hardware JPEG codec, pixel-processing accelerator, and 2D DMA engine handle common imaging and display operations without consuming all the CPU time. Those features point toward smart displays, video doorbells, voice interfaces, industrial panels, and edge-AI sensors rather than simple connected switches.

But with more power comes more responsibility, which means the S31 also gets boosted security. The chip includes secure boot, flash and PSRAM encryption, a true random number generator, key management, a power-glitch detector, trusted execution support, and accelerators for AES, SHA, RSA, ECC, HMAC, and digital signatures.

Consolidation is the real upgrade; the LED is just nostalgia

The S31’s real achievement is consolidation. Jobs that previously needed an ESP32, an Ethernet-capable host, and additional radios can now be run on a single platform. Espressif supports it through ESP-IDF, while ESP-Matter, ESP-GMF, and ESP-BLE-AUDIO extend it into smart home and multimedia roles.

It can still blink an LED, of course, and Espressif’s development board now even includes an addressable RGB one. But with modern wireless protocols, wired gigabit networking, multimedia acceleration, and serious security hardware beside those familiar GPIOs, the ESP32-S31 shows just how far the humble connected microcontroller has come.

Leave a Reply

Your email address will not be published. Required fields are marked *