Power drops during a storm and, within seconds, every phone in the house is on cellular. Your router and modem died with the lights. In plenty of outages, though, the cable or fiber running to the house keeps working, and neither box draws much, so an 18V pack off the garage shelf can keep them running for hours.
I’ve used Ryobi’s 150W power source to get through an outage on tool batteries before, and the router is the next job I’d give it. It works best with some prep. You’ll want rough numbers for your network’s draw and each pack’s runtime, plus a short list of what can stay unplugged.
Check what your router and modem actually draw
Most home networks sip power, but not all of them
Before you grab a pack, add up what your internet depends on. For most homes, that’s two boxes: a modem or fiber ONT, plus a Wi-Fi router. Plenty of ISPs ship one gateway that does both jobs. Expect 5W to 20W from a typical home router. Newer cable modems generally come in below 15W, and fiber ONTs often need less than 10W.
Ryobi leans on that light load in its own marketing. Paired with a 4.0Ah pack, its 150W power source is rated to run an 8W router for about seven hours.
Bigger setups change the math. My UniFi Dream Machine, which replaced my ISP’s router, lists a 26W maximum. That still sits far below the inverter’s 150W limit, so the power source can handle it. The catch shows up in runtime, and it grows fast when a PoE switch and more access points share the battery. For a worst-case figure, multiply the output volts by the amps printed on each power brick. A plug-in watt meter will show the real number.
Turn amp-hours into hours of Wi-Fi
Convert the label to watt-hours
The big number on a Ryobi pack is amp-hours, and that’s only half of what you need. Multiply it by 18V to get watt-hours. That works out to 72Wh for a 4.0Ah pack and 108Wh for a 6.0Ah.
Not all of that reaches your router. The power source steps 18V DC up to 120V AC, then the router’s adapter converts it back down, and each stage wastes some energy. Plan on getting about 80% of the label figure. Ryobi’s seven-hour claim lands right around there.
Divide what’s left by your total load for a ballpark runtime. At 15W, figure on roughly 3.8 hours from a 4.0Ah pack, or 5.8 from a 6.0Ah. Bump the load to 25W and those drop to about 2.3 and 3.5 hours. A 40W network gets around 1.4 hours on the smaller pack and 2.2 on the larger.
Since August, Ryobi has sold its High Performance packs under a new name, 18V ONE+ Lithium. The watt-hour math doesn’t change with the label.
Rehearse the setup before the storm
A test run takes five minutes
A blackout is a bad time to learn the modem’s power brick is wedged behind a media cabinet. Trace both cords now and label the plugs. If you have gear tucked in a basement or closet, keep a short extension cord nearby. That lets the power source sit flat on a shelf.
Do a dry run on a normal afternoon. Ryobi’s 150W units have a single AC outlet, so plug a small splitter into it and move the modem and router onto that. Start with the modem or ONT, and wait about a minute for it to sync before you plug in the router. Confirm the internet returns, and note how long the whole process took.
Some versions of Ryobi’s 150W unit, including the RYi150BG, output a modified sine wave rather than the smoother power a wall outlet delivers. Most router adapters tolerate it without complaint. If one buzzes or gets hot during your test, unplug it and check with the router maker before you count on that pairing.
A test only proves your side of the connection, though. Your provider’s equipment down the street needs electricity too, so a widespread outage can still knock you offline no matter how well your router is fed.
Power only the gear that keeps you online
Every extra device on the inverter shortens your runtime. Smart home hubs, Ethernet switches, and mesh satellites tend to ride on the same power strip as the router, and that whole strip ends up on the battery out of habit. Plug in the modem and router on their own instead.
Mesh systems take a bit more thought. The main node has to stay powered because it connects to the modem, while satellites can stay off if everyone gathers near the main unit.
My own network shows what trimming looks like. My Dream Machine doesn’t have a built-in Wi-Fi radio; it and a separate PoE switch feed four access points mounted in my ceilings. That switch and its radios add a constant draw. In an outage, I’d leave the switch off and use just one access point for Wi-Fi access.
Plan for the battery swap
Pulling the pack restarts the router
The power source stops delivering power the instant you slide the battery off, so the router reboots with every swap. A basic router comes back in a minute or two, while a more capable unit like the Dream Machine takes longer to finish booting. Time your swaps for when nobody’s on a video call, and keep the next pack charged and within arm’s reach.
My spare 18V packs live in a heated garage held around 50–55°F through the winter, so they’re never cold-soaked when I grab one. Top up every pack as soon as a storm appears in the forecast. A drill can finish a job on half a battery, but a router running overnight needs every watt-hour you can give it.
- Color
-
Green
- Tool Type
-
Power Inverter
Keep one pack set aside for the router
Your modem and router need so little that a single 18V pack buys hours of internet. Add a second, and you’re likely covered past bedtime. Choose one charged battery to live next to the power source, the splitter, and the extension cord. When the lights go out, the switchover takes less than a minute, and everyone in the house stays connected. If you’re deciding which packs deserve that spot, my rundown of every Ryobi ONE+ battery I own covers which capacities earn their price.