Managing router settings isn’t the most exciting thing in the world, and even when you do bother, security is probably the last thing you touch. To be fair, most router defaults are sensible enough that you don’t need to worry much. But that doesn’t mean you should trust them blindly, and WPS is a good example. It’s there to help you connect devices quickly, but it also leaves a door open that most people never realize exists, let alone close.
WPS makes connecting to Wi-Fi easier
Push a button or punch in a PIN
WPS is short for Wi-Fi Protected Setup. It’s a feature that lets you connect devices to your network without typing out the password. This makes a lot of sense for devices like printers, smart speakers, smart TVs, or Wi-Fi extenders, where typing a strong, complex password can be annoying. It’s also handy when you need to connect a guest to your Wi-Fi network without sharing the password. That’s the whole deal about WPS. It’s a convenience feature that routers have offered for a couple of decades now.
Depending on your router, WPS works in two ways. First is the push-button method. If your router supports this, you’ll see a dedicated WPS button on it. Press it, and it’ll switch to pairing mode for around two minutes. You’ll also see a blinking light indicating that the mode is activated. You then need to enable the WPS mode on the device you want to connect, and both devices will pair up automatically.
Second is the PIN method, which works a bit differently. Instead of a button press or the password, you need an 8-digit PIN to connect devices. Most routers have the default WPS PIN printed on the back, but if not, you can head to your router’s settings page and look for the WPS option under Network or WLAN to find or generate the PIN. Once you have it, enter it in the password field to connect your device. The router treats the PIN as password proof, which is handy if you’ve set up a long, complex password that’s a pain to type. This method is especially useful if your router is tucked away in some place that’s hard to reach.
Both these methods essentially solve the same problem. They make it easy to connect devices to your Wi-Fi and save you the hassle of sharing passwords.
WPS is convenient, but it could leave your network vulnerable
Convenience comes at a cost
WPS is actually a useful feature when you want to use it, but it’s also a security risk. Let’s talk about the push button method first. When you hit that button, your router drops into pairing mode for any device in range, not just yours. The chances of this being a problem in your house are obviously slim, but if you’re an apartment building or some densely-populated area, this two-minute window does leave you vulnerable.
The PIN method is worse, because it doesn’t come with that two-minute limit. The PIN remains acceptable as long as WPS is enabled on your router. Now, I know what you’re thinking. An 8-digit PIN is 100 million possible combinations. But the thing is, the router doesn’t verify the PIN as a whole. It checks it in two halves and tells the connected device whether each half was correct or not. That design flaw reduces the real number of guesses needed down to around 11,000.
There are also dedicated tools that can attack this vulnerability. Sure, some newer routers try to defend against this by locking out repeated failed PIN attempts, but that’s not the case with older routers. In some cases, even those lockout mechanisms have workarounds.
And the risk here isn’t just someone using your bandwidth. Once an attacker is inside your network, they can snoop on unencrypted traffic or prob other gadgets on the network.
I don’t need WPS turned on all the time, so I turned it off
I can still have it both ways
Connecting new devices to your Wi-Fi network isn’t something you need to do every day, of course. So there’s no point in leaving WPS enabled all the time. I turned it off on my router, and it was pretty easy. All I had to do was log into my router’s settings page, head to Local Network > WLAN > WPS, and disable it.
Not all routers ship with WPS enabled by default. Heck, some don’t even have WPS anymore, especially the newer mesh systems that have moved on from it entirely. So yes, depending on your router model, you might not have to do anything. If you still want the convenience, you can always re-enable WPS for a short window of time and then turn it off manually. That gives you the best of both worlds.