17 - Nov - 2026

6 PC hardware settings where choosing the biggest number is actually a mistake

When it comes to new tech, bigger numbers are what we all want. Faster Wi-Fi, more CPU cores, larger headphone drivers… the list goes on. We’re all susceptible to it, too. I’m not going to sit here and pretend I’m a consistently enlightened consumer who’s never wowed by “number get bigger.”

But there are times when that bigger number really isn’t all it’s made out to be, and we’d be better off taking a step back, because sometimes, the biggest number is a mistake.

RAM speed

Your hardware can’t even keep up

RAM is one of the most frequent “higher number is better” PC hardware purchases, where you’ll be convinced that buying the fastest RAM possible will deliver instantly better performance.

It’s not the case. You could absolutely buy a DDR5-8400 RAM kit, but most of the time, you’ll be leaving performance on the table with a much larger outlay. In some cases, with certain hardware, it could even give you worse performance than a cheaper RAM kit.

A prime example is AMD’s AM5 platform and its memory controller, which can deliver a 1:1 ratio with the CPU, keeping latency low with DDR5-6000/6400 RAM. Once you move beyond 6000/6400, it moves to a 1:2 ratio that can hurt your performance. While faster RAM speeds are fully supported, there is a line between increasing speed and picking up latency issues.

Intel systems use a different memory control system, so they don’t encounter the same issues, but testing has repeatedly shown that ultra-high RAM speeds yield little in terms of performance while costing significantly more. Hardware Busters found that a DDR5-8000 kit only added around 3.5% in-game performance but cost more than double a 6000 kit.

Simply put, there is very little point in splashing serious cash on a DDR5-8000/8400 RAM kit.

Mouse polling rate and DPI

Have you ever actually tried 8,000Hz?

Front view of a vertical mouse

Polling rate describes how often your mouse reports its position to your PC. At 1,000Hz, that’s once every millisecond. At 8,000Hz, it’s once every 0.125ms. If you’ve never used a mouse with an 8,000Hz polling rate, I can tell you, it’s insanely difficult for most regular tasks.

It’s promoted as a feature that might give you an edge in online gaming, where your movement and reactions need to be ultra-fast to top the competition. But did you know most pro-gamers stick to lower polling rates because 8,000Hz is so twitchy that it can make aiming and rapid movement harder?

DPI (Dots Per Inch) has seen similar enormous increases over the years, with some mice now advertising 30,000 DPI. It’s just like the 8,000Hz polling rate, though — one movement, and your mouse has launched out of your monitor into the stratosphere. If you’re attempting to use higher DPI in your games, you’d only end up reducing the in-game sensitivity to compensate, defeating the object.

In reality, most folks need a polling rate between 1,000Hz and 2,000Hz, and maybe up to 4,000Hz, and something in the 800 to 3,200 DPI range is the sensible middle.

Monitor sharpness

Sometimes, less is definitely more

It’s tempting to crank up the sharpness to give what feels like extra crispness to your on-screen visuals, but that’s not what really happens.

In fact, it literally can’t, because the pixels are already there, rendered on screen; pushing the sharpness slider up only really adjusts the lighting slightly, tricking your eyes into thinking it looks better.

In fairness, on a low-resolution screen, some sharpness can help to boost an otherwise low-quality picture, but it’s a balance. If you move the slider too far, all of your on-screen elements begin picking up fringes, odd artifacts, and other visual issues that make everything look worse.

What makes this all the more complicated is that there is no universal sharpness number across all monitors. On one, you’ll find the default sharpness set to 50, while on another, it’ll be 0. Other manufacturers include additional processing modes such as Super Resolution or Clarity, further complicating matters.

There are tools you can use to help find the balance, such as Lagom’s LCD Sharpness test. Move the slider to see where the blur begins, or the halos appear, and find the middle point, which is what you’re looking for.

CPU power limits

In fairness, this isn’t a number you’d check when buying

Intel Xeon CPU in replacement LGA 1150 consumber motherboard

When you buy a new CPU and motherboard, there is often one setting you’d never think to check: the CPU power limit. Your CPU has power limits that control how much power it can draw under sustained and short bursts of load.

Many enthusiast motherboards raise those limits well beyond the chipmaker’s guidance, sometimes out of the box, because higher numbers win benchmark charts. That leads to CPU manufacturers shipping new CPUs with the PL1 and PL2 state in the BIOS set to “unlimited,” which means the processor can theoretically draw as much power as it wants, depending on the cooling system.

Most of the time, your CPU will thermal-throttle once its power draw starts pushing its temperatures sky-high, but it’s not something you should expose your CPU to. Those ultra-high temperatures can cause damage to your CPU and motherboard if not managed properly.

There is a balance to be found with the PL1 and PL2 levels, mind. You can unlock more CPU performance with a custom PL configuration, but it’s CPU-specific, so you’ll need to check your specific hardware. Don’t just throw any old values in there that you find online.

Wi-Fi channel width

Bigger feels better, but it’s just more noise

windows 11 wifi settings showing wifi 7 connection with wpa3 security.

Wi-Fi channel width determines how much of the Wi-Fi spectrum your broadcast uses, and is largely dependent on the Wi-Fi band you’re using. It often feels like increasing your Wi-Fi channel width will instantly deliver better internet, but cranking the width isn’t as simple as it seems.

That’s because the wider you make your Wi-Fi channel, the more likely you are to encounter interference, be it from other Wi-Fi networks, devices in your home, or otherwise.

If you live in the middle of nowhere with very few neighbors, you could safely increase your Wi-Fi channel width without running into too many problems due to the lack of competing signals. But in a busy location, you’re far more likely to encounter other signals, which can actually interfere and slow your network down.

It also depends on the Wi-Fi band you’re using. The 2.4GHz channel only spans around 83.5MHz in total, so increasing your Wi-Fi channel width from the default 20MHz to, say, 40MHz, means you’re covering half the available spectrum and bound to encounter some issues.

You have more available spectrum on the 5GHz and 6GHz bands, making widths of 80MHz, 160MHz, and even 320MHz (on the 6GHz band) available, but that doesn’t mean they’re fully absolved of the interference issues.

Now, that’s not to say you can’t increase your Wi-Fi channel width. It’s just a balancing act depending on your network; cranking it all up to 160MHz is definitely not the way, though.

Windows audio sample rate

Don’t crank it to 11, man

windows 11 audio properties default sample rate.

Buried in your speaker or headphone audio properties are options for different sample rates, wherein you can increase your sample rate up to a maximum of 24-bit, 192,000Hz. That sounds great, right? Higher sample rates must equal better audio, because again, numbers are bigger.

It’s not entirely wrong, but that’s not how this setting works. Windows’ default shared audio mode plays all audio through the same mixer, which runs at a single sample rate. So you can crank up the sample rate in the Audio Properties sample rate menu, but it won’t actually make a specific difference to your audio output.

There is another issue here, too: the audio file you’re playing probably doesn’t support such high sample rates to begin with. The audio detail available to you is limited by the audio file, and is also affected by other decisions, such as playing the audio via a streaming service or locally, using wired headphones or wireless, and so on.

A high-quality FLAC file playing locally on wired headphones is a very different proposition from a high-quality Spotify stream playing on Bluetooth headphones; the latter adds more audio processing at each phase, which can negatively affect your audio even with the best intentions.

The middle of the slider is the golden zone

None of this means the top setting is always wrong. A well-tuned monitor can handle its fastest overdrive mode, a high-end CPU won’t flinch at 8K polling, and a quiet 6GHz network will happily run 160MHz channels (or even 320MHz).

The biggest number isn’t a mistake by definition. It’s a mistake by default, because it gets picked without being tested.

Leave a Reply

Your email address will not be published. Required fields are marked *